Well impressed for the money it fees. I have to acknowledge i was not anticipating the make excellent i saw in this. I acquired this as a speculative obtain to see if the amp itself could be employed for complete range operation and not only sub bass as i have been tasked to arrive up with the best transportable pa process for our choir. By natural means i had to dig close to within and was shocked at what i identified. This is a one output not bridge tied loiad, it can be 2ohm steady and can output 100w rms into an 8 ohm load or 200w rms into a pair of eight ohm drivers in parallel.
The low go filters are on a daughter board and the link to the motherboard has a whole vary enter. The only way it could have turned out greater is if out was stereo lol. The notice to detail in the structure even has printedmarks on via the board element/hyperlink prospects to indfindicate which course the prospects really should be bent about towards, presumably to keep away from accidental solder bridges later on on in creation. First time i have observed that in a low price tag consumer devicein concept i could acquire a second just one of these and make a btl phase splitter daughter board and bridge two of these to get 600w rms into 4ohmspossibly 1200w peak. I did observe in my initial investigation that this amp is however shown on the kenwood web-site so it is most likely it is not a discontinued product.
Pros
|
Features of Kenwood KAC-6104D Class-D Mono Power Amplifier with 600W Max Power
- Width:19.8 cm
- Weight:1.8 kg
- Product Type:Amplifier
- Recommended Use:Car
- Height:5.9 cm
Amplifier Class:Class D, Amplifier Output:1-channel, Crossover Slope:twelve dB/octave, Frequency Response:twenty - two hundred Hz, Max Output Power / Channel Qty:600 Watts x 1, Continuous Power / Channel Qty:200 Watts x one, Crossover:Active crossover, Signal-To-Sounds Ratio:94 dB, Output Power / Complete:600 Watt, Large Stage Inputs:Of course, Amplifier Output details:two hundred Watt - four Ohm - 20 - 200 Hz - THD 1.% - 1 channel(s) ¦ 300 Watt - two Ohm - at a hundred Hz - THD 1.% - one channel(s), Lower Go Frequencies:fifty - 200 Hz, Input Sign Voltage:.two - 5V, Connector Kind:Audio line-in ( RCA phono x two ) ¦ Speakers input ¦ Speakers output ( screw-type ) ¦ DC power enter ( screw-sort )
Just what i wanted extremely impressive drives sub and stays chilly took extended time for supply but i'm in the highlands.
Operates my 12' sub really nicely. I have mine managing at 2ohms and has been wonderful for a few months now. Provides a wonderful punchy bass and is definitely perfectly priced for the power.
Product Info
- Product Dimensions: 23 x 19.8 x 5.9 cm ; 1.8 Kg
- Boxed-product Weight: 2.1 Kg
- Item model number: KAC-6104D
- ASIN: B002650WBE
Decent impressive amp for a sub. Powers my 1200w pioneer sub without complaint. A number of settings to enjoy with and a high stage input as perfectly as low make this a universal set up.
I couldn't resist using the back off and owning a peak insidevery quick to set up, with loads of power to generate my sub-woofer. Getting classd it operates virtually chilly to touch, so is very economical. I imagine this item is now discontinued, which is a shame.
If you can get one, they are exceptional value for these kinds of a very good product or service.
Conclusion of Kenwood KAC-6104D Class-D Mono Power Amplifier
I could not resist using the again off and acquiring a peak insidevery easy to put in, with plenty of power to travel my sub-woofer. Remaining classd it operates pretty much cold to contact, so is really productive. I think this product is now discontinued, which is a shame. If you can get a single, they are superb benefit for this kind of a very good product or service.
I have to admit i was not anticipating the establish high-quality i saw in this. I acquired this as a speculative get to see if the amp by itself could be utilized for full vary procedure and not only sub bass as i have been tasked to arrive up with the ideal moveable pa method for our choir. Naturally i experienced to dig all over inside of and was stunned at what i uncovered. This is a single output not bridge tied loiad, it is really 2ohm secure and can output 100w rms into an eight ohm load or 200w rms into a pair of eight ohm drivers in parallel. The lower move filters are on a daughter board and the link to the motherboard has a full range input.
The only way it could have turned out superior is if out was stereo lol. The consideration to element in the design even has printedmarks on through the board ingredient/website link qualified prospects to indfindicate which course the sales opportunities need to be bent in excess of to, presumably to stay away from accidental solder bridges later on in creation. Very first time i've witnessed that in a low price client devicein concept i could get a next just one of these and make a btl stage splitter daughter board and bridge two of these to get 600w rms into 4ohmspossibly 1200w peak. I did detect in my preliminary investigation that this amp is nonetheless outlined on the kenwood web page so it is probably it is not a discontinued product. Have utilised kenwood amps off and on for quite a few yrs now and although they might not be prime on attributes they undoubtedly do the position properly and are trustworthy. (very last amp has lasted 10 a long time) would endorse to any one wanting for a basic monoblock amp. Runs my 12' sub really properly. I have mine functioning at 2ohms and has been high-quality for a handful of months now.
Presents a good punchy bass and is definitely perfectly priced for the power. Good highly effective amp for a sub. Powers my 1200w pioneer sub with no complaint.
A couple configurations to play with and a substantial level enter as nicely as reduced make this a universal set up. Precisely what i needed really potent drives sub and stays cold took long time for supply but i am in the highlands.
Tidak ada komentar:
Posting Komentar